service hotline:
134 2435 5558
online service
 Work Time
Mon to Fri :8:30-17:30
Sat to Sun :9:00-17:00
 Contact Details
Tel:134 2435 5558
website qrcode

Scan to view the mobile website

Product Detail
YDH﹣05B50TA explosion-proof membrane
Share to:

YDH﹣05B50TA explosion-proof membrane

Spec According to customer requirements Material PET
Color Transparent Model YDH﹣05B50TA

1. Features:

   < span style="font-family:Arial;font-size:13px">Product made of transparent polyester filmPET as the substrateSingle-sided coatingpaintedOCAglueConstruction, excellent weather resistance and mechanical properties and dimensional stability

    haslow Adhesion is easy to tear off and no glue residue is left after tearing, with excellent initial adhesion

2. Application areas:

   < span style="font-family:Arial;font-size:13px">The product is widely used in:Applicable For touch, display panel, plastic products and other surface protectionandthe rear cover plate plays a protective role of explosion protection

3.Productsstructure span>


4.Product performance:

Detection items

Test parameters

Test method

substrate with gluethickness ( mm)


Manual test with micrometer or thickness micrometer

Length (M)

according to customer's request

Control the number of meters when the machine is rewinding

width (mm)

according to customer's request

ruler (steel) or tape measure



Visual inspection

Substrate transmittance (%)



Haze (%)

<< span="">8


Heat Shrinkage (%)



Landscape/Longitudinal tensile strength (Mpa)



Temperature resistance (℃)


Take a 25mm wide and 150mm long sample, stick it on the surface of the glass screen, and put it in an oven with 180 ℃ bake1H, relative humidity 65%RH, no glue residue when removed span>



Take a 25mm wide and 300mm long sample, pull apart the release film of the sample, and stick it with the outer surface of 25um PET (non-corona surface), and the width of the sample strip is the same as that of the pasted PET, and there should be no excess edges or gaps. Use a 2kg roller to roll back and forth without pressure for 3 times. After standing for 20 minutes, the tensile tester clamps the 25um PET film. /span>180 degree peeling, take the average value of the test curve

5. Storage requirements:

   < span style="font-family:宋体;font-size:13px">Warranty period: original packaging, from the date of shipment from Yongdahui6 months, store in the environment of 23±2℃, 55±5%RH humidity, avoid direct sunlight and high temperature (40℃ above), high humidity (70%RH above), low temperature (0℃ Below) and other conditions for storage and placement.

6. Important note:

   < span style="font-family: 宋体;font-size:13px">The bonding strength depends on the amount of glue on the bonding surface. The stable pressure during operation can improve the contact performance and bonding strength of the adhesive. The joint surface must be clean, dry and even.

   < span style="font-family:宋体;font-size:13px">The parameter values listed are the average values obtained by relying on our equipment, environment and testing methods, and are not the fundamental basis for customer judgment. In order to ensure the applicability of the product, customers are advised to test and judge according to their test methods. In the early stage of product introduction, our company recommends customers to apply relevant real stickers to ensure product applicability

   < span style="font-family:宋体;font-size:13px">Yongdahui does not make any express or implied warranties, including any warranties of special purpose, commerciality or applicability.

Building A, No. 1, Jinyuan 4th Road, Xinqiao Community, Xinqiao Street, Baoan District, Shenzhen
134 2435 5558
Working hours:09:00—18:00
Contact Us: